Share your referral link via Email

Will your rails work with the Ruger AR556?

Yes! All of our rails will work with the Ruger AR 556 as well as any other Mil-spec direct impingement AR-15s.  and stocking our current rails.

Hopefully as we grow and are more able to keep up with demand, we'll be able to consider adding different colorway options!

 

Check out other frequently asked questions below! 

 

Barrel Nut Questions

The first place to check if you can't find your barrel nut is the back of the handguard. It is usually pretty hard to see and easily blends in. Loosen the 2 allen bolts and tilt your handguard so the muzzle end is upwards. The barrel nut should slide out. 

If for some reason you still can't find your barrel nut after following the above steps, click the "Leave us a message" button and we will get you squared away. You can also email support at support@stngrusa.com. 

So the steel barrel nut is going to be stronger and can be torqued down to a higher value than the aluminum version. The steel will also last longer if you plan on torquing it down multiple times. 

The torque value for the steel is: 30-80ft/lbs while the torque range for the aluminum is: 30-60 ft/lbs

With that said, the steel (3.29 ounces) version is heavier than the aluminum (1.4 ounces). If you are going for a super lightweight build, then aluminum is your best bet. However, if you don't mind the extra weight and want the strongest option we carry, then steel is the way to go.  

Handguard Questions

All of our handguards are proudly made in the USA from US aluminum and are in compliance with the standards put forth by the Federal Trade Commission (FTC). This has been 3rd party verified by Made In The USA Brands. You can read more about the certification process HERE 

Is there really any other way to do it?

As a rule of thumb, most "Low profile set screw" gas blocks will work (unless listed below). Clamp on style gas blocks will work as well, however, the screws may need to be slightly modified to allow for proper clearance underneath the handguard. 

Most gas blocks with an ID of (.625", .750" or .875) should work while .936" will NOT work. 

The following brands offer gas blocks that will NOT work: 

-Odin Works (Only the "Low Profile Gas Block" model will work)

-JP Enterprises (No models work) 

-YHM (Pinch Screw)

*Same rules apply for adjustable gas blocks. 

Common adjustable gas blocks that will work:

-SLR Sentry (modification may be required for clamp on version)

-Superlative Arms (modification may be required for clamp on version)

-Any other gas blocks with similar dimensions

So typically the tabs need to be removed with billet uppers because they are too wide for the handguard.

However, it is possible to save most of the tabs with some uppers. You still have to grind off part of the tab, however, if you remove some of the inside (instead of just taking them off all together) it will work. Basically you just need to slowly remove the inside of the tabs until they fit. Depending on your upper, this allows you to keep the tabs and allow the handguard to fit.

Our rails are designed to work with Mil-spec direct impingement AR-15s. 

Billet and side charging uppers may require modification to the handguard to work.

Non Mil-spec threaded uppers such as the Bushmaster Carbon series will not work. 

Right now we only offer our rails in anodized black. Sorry about that!

Unfortunately, bull barrels combined with their gas blocks are too wide to allow our handguards (1.35" inside diameter) to fit over and will not work. Sorry about that! 

Our handguards are not compatible with most piston systems and are designed to work with direct impingement style firearms. 

Unfortunately, our handguards do not work with the Dolos system. Our barrel nuts use the standard 1.25" x 18tpi which is different than what is used in the Dolos system.

The cut-out on the HWK rail comes back about 1.06". So the length of each rail up to where the cut-out begins would be found by subtracting 1.06" from the overall length. 

 

Unfortunately, at this time we do not offer rails for the AR10 platform. However, we hope to eventually offer them down the road if there is enough interest in them! 

Unfortunately, we aren't able to offer custom length handguards at this time. 

Our handguards have an inside diameter of 1.35". This allows cans like the Noveske Kx5 and slim KAK slim can to fit underneath them. If your suppressor has a similar diameter as the cans mentioned above, it will work. However, if it is wider then it will unfortunately not be compatible. We don't have plans for a suppressor compatible rail at the moment, but may in the future. 

Other

Send us an email to support@stngrusa.com and we may be able to work out some kind of bulk discount. 

Here is a link to our shipping policies as well as those of UPS and USPS: https://www.stngrusa.com/pages/shipping-service-policies

Yes we do! Send us a message with the items you would like to support@stngrusa.com and we will provide you with mailing instructions. 

Sign up for our newsletter